入水:gate

一、入水:gate
  进入位: gate location
  水口形式:gate type
  大水口:edge gate
  细水口: pin-point gate
  水口大小:gate size
  转水口: switching runner/gate
  唧嘴口径: sprue diameter
  二、流道: runner
  热流道: hot runner,hot manifold
  热嘴冷流道: hot sprue/cold runner
  唧嘴直流: direct sprue gate
  圆形流道:round(full/half runner
  流道电脑分析:mold flow analysis
  流道平衡:runner balance
  热嘴: hot sprue
  热流道板:hot manifold
  发热管:cartridge heater
  探针: thermocouples
  插头: connector plug
  插座: connector socket
  密封/封料: seal
  三、运水:water line
  喉塞:line lpug
  喉管:tube
  塑胶管:plastic tube
  快速接头:jiffy quick connector plug/socker
  四、 模具 零件: mold components
  三板模:3-plate mold
  二板模:2-plate mold
  边钉/导边:leader pin/guide pin
  边司/导套:bushing/guide bushing
  中托司:shoulder guide bushing
  中托边L:guide pin
  顶针板:ejector retainner plate
  托板: support plate
  螺丝: screw
  管钉:dowel pin
  开模槽:ply bar scot
  内模管位:core/cavity inter-lock
  顶针: ejector pin
  司筒:ejector sleeve
  司筒针:ejector pin
  推板:stripper plate
  缩呵:movable core,return core core puller
  扣机( 尼龙 拉勾):nylon latch lock
  斜顶:lifter
  模胚(架): mold base
  上内模:cavity insert
  下内模:core insert
  行位(滑块): slide
  镶件:insert
  压座/斜鸡:wedge
  耐磨板/油板:wedge wear plate
  压条:plate
  撑头: support pillar
  唧嘴: sprue bushing
  挡板:stop plate
  定位圈:locating ring
  锁扣:latch
  扣鸡:parting lock set
  推杆:push bar
  栓打螺丝:S.H.S.B
  顶板:eracuretun
  活动臂:lever arm
  分流锥:spure sperader
  水口司:bush
  垃圾钉:stop pin
  隔片:buffle
  弹弓柱:spring rod
  弹弓:die spring
  中托司:ejector guide bush
  中托边:ejector guide pin
  镶针:pin
  销子:dowel pin
  波子弹弓:ball catch
  喉塞: pipe plug
  锁模块:lock plate
  斜顶:angle from pin
  斜顶杆:angle ejector rod
 
  尼龙 拉勾:parting locks
  活动臂:lever arm
  复位键、提前回杆:early return bar
  气阀:valves
  斜导边:angle pin
  术语 :terms
  承压平面平衡:parting surface support balance
  模排气:parting line venting
  回针碰料位:return pin and cavity interference
  模总高超出啤机规格:mold base shut hight
  顶针碰运水:water line interferes withejector pin
  料位出上/下模:part from cavith (core) side
  模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
  不准用镶件: Do not use (core/cavity) insert
  用铍铜做镶件: use beryllium copper insert
  初步(正式)模图设计:preliinary (final) mold design
  反呵:reverse core
  弹弓压缩量:spring compressed length
  稳定性好:good stability,stable
  强度不够:insufficient rigidity
  均匀冷却:even cooling
  扣模:sticking
  热膨胀:thero expansion
  公差:tolorance
  铜公(电极):copper electrode ...

发表评论:

◎欢迎参与讨论,请在这里发表您的看法、交流您的观点。

控制面板
您好,欢迎到访网站!
  查看权限
网站分类
    标签列表
      文章归档
        友情链接

        Powered By Z-BlogPHP 1.5 Zero

        Copyright Your WebSite.Some Rights Reserved.